About Photo-Catalyst

1.1) What is a Photo-Catalyst?

A Photo-Catalyst is a substance that promotes a chemical reaction when exposed to sunlight or Ultra Violet (UV) Light. It does not require any other special / expensive form of energy and uses only clean energy found abundantly in everyday life. Titanium Dioxide is a Photo-Catalyst that has strong Photo-Catalectic Reaction Properties and effectively decomposes organic matter cleanly and safely. However it requires a certain time frame to break down huge amounts of organic matter and gases.

1.2) What is Titanium Dioxide?

Titanium Dioxide (Ti02) is a harmless ceramic mineral which can be found in various materials and Foods. Food Additives, Cosmetics, Sun Block Creams / Lotions, Ice-Cream Pigment, Toothpastes and Soaps are common items that contain Ti02. Other items include White Paint Pigment, Electronic Components, Fibre / Textile Products and et cetera. Ti02 has recently attracted world-wide attention for its effective Photo-Catalectic reaction. It is also a chemically stable mineral when exposed to a light source and promotes ‘Green Technology’ for the environment.

1.3) Photo-Catalyst Stroke Chart

Organic Matter is decomposed into Water Vapour and CO2 Gas.

1.4) Principle of Reaction

Hydroxyl Radical and Super Oxide Anions are strong Active Oxygen. They are capable of breaking down various forms of organic matter.

Light Spectrum

The light spectrum is divided into different Fig1 Light Spectrum Chart wavelengths according to the nanometre range. The Ultraviolet (UV) Light strength is 2 - 3 mW/cm2 and is found in sunlight. The UV Light strength is reduced by several micrometerW/cm2 whilst indoors. The reduced amount is approximately one thousandth of a part. Current photo-catalyst manufacturing companies are utilizing photo-catalyst compounds that can only react with UV Light. Both natural and artificial (fluorescent) light produces UV Rays. For these photo-catalysis compounds, the wavelength used is below 387 nm which amounts to only 3 % of the amount of fluorescent light energy being produced. The EnviroCare M1-S Ti02 Photo-Catalyst (Photo-Compound) for textiles is capable of reacting to wavelengths of visible light. Hence its photo-catalyst ability can respond by up to 480 nm. The spectrum wavelength of 480 nm is the Colour Blue which amounts to 25% of fluorescent light. Therefore the EnviroCare M1-S Ti02 Photo-Compound is more effective because of a broader light spectrum being used than most photo-catalyst compounds found in today’s market.

Fig1. Light Spectrum Chart

Lifespan Test

The EnviroCare M1-S Ti02 Photo-Compound for Textiles is applied onto textiles which are subsequently washed for up to fifty (50) times and was again tested with the same microbial showing no signs of product ability diminishing confirming the product lifespan and capability; and photo-catalyst effect.
Both Tests were conducted by SETSCO who is an independent party and test results can be viewed upon requests

Both Tests were conducted by SETSCO who is an independent party and test results can be viewed upon requests

About The Envirocare M5 Ti02 PhotoCompound

1.1) What is the EnviroCare M5 Ti02 PhotoCompound

The EnviroCare M5 Ti02 PhotoCompound is a Titanium Dioxide (Ti02) based Photo-Catalyst High Transparency substance that promotes a chemical reaction when exposed to Sunlight or Fluorescent Light. It does not require any other special / expensive form of energy and uses only clean energy found abundantly in everyday life. Conventional Ti02 Photo-Catalyst Compounds can only harness energy from the UV light spectrum. Ti02 have strong Photo-Catalectic Reaction Properties and effectively decomposes organic matter cleanly and safely. However it requires a certain time frame to break down huge amounts of organic matter and gases.

Fig2. Light Spectrum Chart

Decomposition (Comparison Trial)

Photo1 is a direct comparison between an UV Light reacting type of photo-catalyst compound and the EnviroCare M5 PhotoCompound Visible Light reacting compound. Both samples are exposed to only fluorescent light and under the same conditions

The EnviroCare M5 PhotoCompound is more effective in performance and has a higher degradable capability than the standard UV Light reacting type. This is due to the broader wavelength being used and can respond faster and more efficiently by up 5 times when compared to the conventional UV Light Reactive type of photo-catalyst

Methylene Blue Ink Drops are applied onto each tile / The tiles are exposed to UV Light for 10 hours.
Silver photo-catalyst EnviroCare M5 Silver photo-catalyst EnviroCare M5 compound PhotoCompound compound PhotoCompound.

Comments:
Silver Photo-catalyst compound :
The Photo-catalysis ability is ineffective and the Methylene blue spots are still present.

EnviroCare M-5 PhotoCompound:
All Methylene blue spots are decomposed effectively and thoroughly after 10 hours. This test confirms the distinct difference between the M-5 and other photo-catalyst brands

Comparison test with other photo-catalyst compounds (ie. silver)

Red ink is applied via spray gun onto each tile.

Comments:
Silver Photo-catalyst compound :
The Photo-catalysis ability is ineffective and the Red Ink Stains are still present.

EnviroCare M-5 PhotoCompound:
All Red Ink Stains are decomposed effectively and thoroughly after 42 hours. This test confirms the distinct difference between the M-5 and other photo-catalyst brands.

Comparison test with other types of photo-catalyst fluid and pre-coated tile

Red ink is applied via spray gun onto each tile.
T company manufactures TiO2 coated tiles.
S company manufacture’s TiO2 fluid which is buff yellow and is water based.
EnviroCare Ti02 M5 Photo-Compound can react to visible light effectively.
Centre tile is original in state (for comparison purpose)

The tiles are exposed to sunlight for 15 minute.

EnviroCare Ti02 M5 Photo-Compound is able to show a higher decomposition rate compared to the other coated and compound applied tiles.

The tiles are exposed to sunlight for 15 minute.

EnviroCare Ti02 M5 Photo-Compound is able to show a higher decomposition rate compared to the other coated and compound applied tiles.

Decay Durability Tests

(1)      Weather Resistant Test The EnviroCare M5
          PhotoCompound coated tiles are exposed and tested
          by an accelerated weathering process of 300 hours.
          This test is to confirm any exfoliation and photo-
          catalyst effect.

(2)      Exposure Test The EnviroCare M5 PhotoCompound
          coated tiles have been exposed to weather since
          June. 16. 2003 (the tiles were also subjected to a
          weather resistant test). The right side of the steel plate
          is coated with the EnviroCare M3 PhotoCompound; and
          the complete plate has been exposed since January.
          30. 2001

About The Envirocare M7 Ti02 PhotoCompound

1.1) What is the EnviroCare M7 Ti02 PhotoCompound

PhotoCompound is a Titanium Dioxide (Ti02) based Photo-Catalyst High Transparency substance that promotes a chemical reaction when exposed to Sunlight or Fluorescent Light. It does not require any other special / expensive form of energy and uses only clean energy found abundantly in everyday life. Conventional Ti02 Photo-Catalyst Compounds can only harness energy from the UV light spectrum. Ti02 have strong Photo-Catalectic

Fig2 Light Spectral Distribution

1.    Red ink is applied via spray gun method on each tile.
       T company manufactures TiO2 coated tiles.
       S company manufacturesTi02 fluids which is buff yellow
       and is water based.
       The M5 Ti02 Photo-Compound reacts effectively to visible
       light. The M7 Ti02 Photo-Compound reacts effectively to
       visible light.

2.    Exposure to sunlight after 15 minutes.

      The M5 and M7 Ti02 Photo-Compound treated tiles were
      able to show a higher level of decomposition capabilities
      compared to most other coated and treated tiles.

Decay / Decomposition Durability

Weather Resistant Test

The M7 Ti02 Photo-Compound coated surfaces were subjected to an accelerated weathering test of 300 hours. The test was conducted to determine whether exfoliation and the loss of hydrophilic properties occur.

Exposure Test

The M7 Ti02 Photo-Compound coated surfaces were left exposed since June. 20. 2005. These coated surfaces were also subjected to the Weather Resistant Test of 300 hours (above mentioned tests) This test confirms non-self-cleaning capabilities for non-treated surfaces and the appearance of water spots whereas M7 Ti02 Photo-Compound and M7 BaseCoat coated tiles remain impressive in nature.

1.   Non-Coated glass surface

Hydrophobic capabilities on Glass surface remains and water spots and droplets are easily formed; and transparency is greatly affected.

2.   Glass surface coated with only M7 Ti02 Photo-Compound and M7 Alcohol BaseCoat

Glass surface remains hydrophilic in nature and no problems with transparency.

3.   Coated with only M5 Ti02 Photo-Compound

Majority part of glass surface (mainly centre) remains hydrophilic. However, girth of silicone appears around the glass edges which leads to hydrophobic surface state and transparency is below par at these areas.

4.   Coated with only M7 Ti02 Photo-Compound

Glass surface remains hydrophilic in nature and no problems with transparency.

About The Envirocare M8 Ti02 PhotoCompound

1.1) What is the EnviroCare M8 Ti02 PhotoCompound

PhotoCompound is a Titanium Dioxide (Ti02) based Photo-Catalyst High Transparency substance that promotes a chemical reaction when exposed to Sunlight or Fluorescent Light. It does not require any other special / expensive form of energy and uses only clean energy found abundantly in everyday life. Conventional Ti02 Photo-Catalyst Compounds can only harness energy from the UV light spectrum. Ti02 have strong Photo-Catalectic

Fig2 Light Spectral Distribution

1.    Red ink is applied via spray gun method on each tile.
       T company manufactures TiO2 coated tiles.
       S company manufacturesTi02 fluids which is buff yellow
       and is water based.
       The M5 Ti02 Photo-Compound reacts effectively to visible
       light. The M8 Ti02 Photo-Compound reacts effectively to
       visible light.

2.    Exposure to sunlight after 15 minutes.

      The M5 and M8 Ti02 Photo-Compound treated tiles were
      able to show a higher level of decomposition capabilities
      compared to most other coated and treated tiles.

Decay / Decomposition Durability

Weather Resistant Test

The M8 Ti02 Photo-Compound coated surfaces were subjected to an accelerated weathering test of 300 hours. The test was conducted to determine whether exfoliation and the loss of hydrophilic properties occur.

Exposure Test

The M8 Ti02 Photo-Compound coated surfaces were left exposed since June. 20. 2005. These coated surfaces were also subjected to the Weather Resistant Test of 300 hours (above mentioned tests) This test confirms non-self-cleaning capabilities for non-treated surfaces and the appearance of water spots whereas M8 Ti02 Photo-Compound and M8 BaseCoat coated tiles remain impressive in nature.

1.   Non-Coated glass surface

Hydrophobic capabilities on Glass surface remains and water spots and droplets are easily formed; and transparency is greatly affected.

2.   Glass surface coated with only M8 Ti02 Photo-Compound and M8 Water BaseCoat

Glass surface remains hydrophilic in nature and no problems with transparency.

3.   Coated with only M5 Ti02 Photo-Compound

Majority part of glass surface (mainly centre) remains hydrophilic. However, girth of silicone appears around the glass edges which leads to hydrophobic surface state and transparency is below par at these areas.

4.   Coated with only M8 Ti02 Photo-Compound

Glass surface remains hydrophilic in nature and no problems with transparency.

EnviroCare K1 T102 PhotoCompound Bactericidal and Odour Eliminating Spray

The EnviroCare K1 Ti02 Photo-Compound Hand Held Spray can be applied onto almost any surface for the destruction of bacteria and bacteria causing odours for short periods as compared to the standard chemical / solvent based disinfectant(s) found in the market.

The Compound should be applied onto surfaces that have already been cleaned to prevent further build-up of bacteria and bacterial causing odours and thus acts as a mild disinfectant which is safe for human contact. It has a lifespan of up to a week (depending on location of use); however, it is not semi-permanent unlike the EnviroCare Ti02 Compound Range.

The EnviroCare K1 Ti02 Photo-Compound Hand Held Spray comes in a 120ml / 250ml bottle with a built-in spray nozzle for easy handling, application and storage; and is also affordable.

The EnviroCare K1 Ti02 Photo-Compound can also be used as an affordable fogging agent and the fogged room can be used almost immediately after treatment. Hence there is no downtime whatsoever, unlike other chemical based fogging products. For fogging, we recommend the purchase of 5.0litre containers.

The EnviroCare K1 Ti02 PhotoCompound does not contain any carcinogens and other caustic chemicals. Hence it is safe for constant and continuous use without compromising your health and the environment.

Fundamentals of Bacteria and Odour Eliminating

1.   Introduction

In  recent  years,  the  consumer  has  come  to  demand  a  more  comfortable  living  environment  and  is extremely self-conscious about the smell in one's immediate surroundings.
Titanium Dioxide Photocatalyst products have some success in the destruction of odours. However, there are indoor areas where light is not readily available. Hence Ti02 based products will not have success in such locations effectively
Altimate EnviroCare Services Pte Ltd in conjunction with our Japanese Partners have developed a new
range  of  Bacteria  and  Odour  Eliminating  Compounds  that  are  able  to  absorb  both  high  and  low
concentration of various odours in dark (or no light) enclosed areas quickly, cleanly and safely. Activated
charcoal is known to be able to absorb smell effectively. However the new Bacteria and Odour Eliminating
Compound has proven to be more effective for bacteria and smell elimination than Activated Charcoal.

They are the EnviroCare S1 & S2 Bacteria and Odour Eliminating Compounds

The EnviroClean Detergent is a synthetic detergent with an alkalescent of PH 10.5 that was originally designed to sanitise and sterilise medical instruments.

Because of its ability to create an extremely high amount of oxygen when added to water and having minimal soapiness, it was soon discovered that the detergent works effectively as a residential cleaning agent. Thus cooking utensils, floor, house & glass cleaning, clothes / textile washing can now use the EnviroClean Detergent. This helps to minimise the buying of various home cleaning agents and furthermore, it is synthetic and not chemical / alcohol based, hence it is safe for prolonged human contact.

It does not use any carcinogens and caustic chemicals. Hence it is safe to use constantly and continuously without compromising your health and the environment.

The fast acting, EnviroClean Detergent dissolves almost instantly in warm water, creating a high level of oxygen that helps destroy bacteria and odours. It can be used around the house for laundry (both textile and synthetic fabrics), tableware, kitchen table surfaces, cooking utensils, bathtubs, tiles.

The EnviroClean Detergent is extremely effective on metallic surfaces and can be used to clean and wash very precious metals (and all other standard metals) for the removal of fungi, algae, mould and even oil

The EnviroClean Detergent can also be used effectively as a carpet cleaning agent and has the ability to clean even Persian Carpets without discolouration being a nightmare. It can be added into wet / dry vacuum cleaners and is more cost effective than most other cleaning agents with the same abilities.

The ‘do-away-with rinsing’ phenomenon allows the detergent to be used with minimal rinsing required, hence saving you electrical and water costs and helps care for the environment too.

The EnviroClean Detergent comes in a 750ml Plastic Container with Screw-On cap for easy storage

Nonionic Surface Active Agent, Secondary Alcoholic Ethoxylate, Percarbonate, Carbonate, Organic Cleathing Agent (Non-Phosphates)

Standard wash :15 – 20 grams per 30 litres of warm water (for laundry use) / 5 grams per 3 litres of hot water (for dishwashing use and other household use).

For stubborn stains, pre-soaking might be required with 25-30 grams per 30 litres of warm water (for laundry use)  / 10 – 15 grams per 3 litres of hot water (for dishwashing and other household use).